The communication protocol of the controller is not publicly available, so it is not possible to access data directly from the controller.
However, you can transfer data to other software using the API functionality in our software.
Controller ▶ Other Software (X)
Controller ▶ Kitronyx Software ▶ Other Software (O)
If you have any other inquiries, please leave a message through the URLs below, and we will respond promptly.
For product inquiries: https://www.kitronyx.com/contact
For technical support inquiries: https://www.kitronyx.com/support_request
Hello, this is Kitronyx.
It is common to encounter situations where a controller must be placed inside a vacuum chamber for pressure mapping measurements.
We conducted tests to confirm if a controller can be used under such conditions.
Tested Controller: Baikal II WIFI
Test Conditions:
The Baikal II WIFI model is equipped with an internal battery.
According to the battery manufacturer, the battery operates without issues at 87 Torr for up to 6 hours.
The Baikal II controller can read a maximum of 48*48 sensor channels (a total of 2304 channels).
Therefore, the maximum number of sensors that can be connected depends on the number of channels per sensor.
Example:
SFC4300CX (48*48 Ch = 2304 channels) -------------- Maximum 1 unit
Custom Sensor (48*12 Ch = 576 channels) 576 * 4 = 2304 channels ----- Maximum 4 units
* For simultaneous connection of custom sensors, a separate interface board development is required.
* Please note that the number of sensors may vary depending on the design of the custom sensor.
Contact our sales team for further information.
The power consumption for each controller is as follows:
Model
Power Source
Remarks
Baikal II
USB Powered, +5V / 0.8A max
Baikal II WIfI
USB Powered, +5V / 1.5A max
In wireless mode, the controller uses a Lithium polymer battery, 3,000mAh
For more detailed information, please refer to the specific product pages.
※ Depending on your PC environment, if you are using more than three controllers,
it is recommended to use a USB hub that provides separate power.
The dimensions for each controller are as follows:
Out Dimension ( L x W x H ) (mm)
Tinn
70.54 x 108.65 x 27.04
156.86 x 80.9 x 22
Baikal II Wifi
170 x 70 x 30
The Tinn / Baikal II wired products communicate with a PC via USB.
The Baikal II Wifi product is a dual-mode product that communicates with a PC via both USB and Wifi (2.4GHz, 802.11 g/n).
For other communication environments (such as RS232), custom development is required.
Please contact our sales team for further information.
Sales@kitronyx.com
The measurement speed of the Baikal II depends on the communication environment:32Hz in a wired environment and 21Hz in a wireless environment.
For faster measurement speeds, custom development is required.
We have developed solutions up to 600Hz.
Please refer to the demo video linked below.
The controller itself does not support data storage or output functions.
If you use external programs and separate data processing devices (PLC, DAQ, etc.),
you cannot directly connect and communicate with the controller.
However, you can receive data through the PC software connected to the controller.
With the purchase of a controller, a controller test board is provided to check for any malfunctions.
For detailed information, please refer to the attached Controller Test Board User Manual.
controller test board manual_240715.pdf
The controller test board will be provided from the new controller package starting in April 2024.
Please inquire if you need a controller test board.
Link to how to use the controller test board
The communication protocol of the controller is not publicly available, so it is not possible to access data directly from the controller.
However, you can transfer data to other software using the API functionality in our software.
Controller ▶ Other Software (X)
Controller ▶ Kitronyx Software ▶ Other Software (O)
If you have any other inquiries, please leave a message through the URLs below, and we will respond promptly.
For product inquiries: https://www.kitronyx.com/contact
For technical support inquiries: https://www.kitronyx.com/support_request
Hello, this is Kitronyx.
It is common to encounter situations where a controller must be placed inside a vacuum chamber for pressure mapping measurements.
We conducted tests to confirm if a controller can be used under such conditions.
Tested Controller: Baikal II WIFI
Test Conditions:
The Baikal II WIFI model is equipped with an internal battery.
According to the battery manufacturer, the battery operates without issues at 87 Torr for up to 6 hours.
If you have any other inquiries, please leave a message through the URLs below, and we will respond promptly.
For product inquiries: https://www.kitronyx.com/contact
For technical support inquiries: https://www.kitronyx.com/support_request
The Baikal II controller can read a maximum of 48*48 sensor channels (a total of 2304 channels).
Therefore, the maximum number of sensors that can be connected depends on the number of channels per sensor.
Example:
SFC4300CX (48*48 Ch = 2304 channels) -------------- Maximum 1 unit
Custom Sensor (48*12 Ch = 576 channels) 576 * 4 = 2304 channels ----- Maximum 4 units
* For simultaneous connection of custom sensors, a separate interface board development is required.
* Please note that the number of sensors may vary depending on the design of the custom sensor.
Contact our sales team for further information.
If you have any other inquiries, please leave a message through the URLs below, and we will respond promptly.
For product inquiries: https://www.kitronyx.com/contact
For technical support inquiries: https://www.kitronyx.com/support_request
The power consumption for each controller is as follows:
Model
Power Source
Remarks
Baikal II
USB Powered, +5V / 0.8A max
Baikal II WIfI
USB Powered, +5V / 1.5A max
In wireless mode, the controller uses a Lithium polymer battery, 3,000mAh
For more detailed information, please refer to the specific product pages.
※ Depending on your PC environment, if you are using more than three controllers,
it is recommended to use a USB hub that provides separate power.
If you have any other inquiries, please leave a message through the URLs below, and we will respond promptly.
For product inquiries: https://www.kitronyx.com/contact
For technical support inquiries: https://www.kitronyx.com/support_request
The dimensions for each controller are as follows:
Model
Out Dimension ( L x W x H ) (mm)
Tinn
70.54 x 108.65 x 27.04
Baikal II
156.86 x 80.9 x 22
Baikal II Wifi
170 x 70 x 30
For more detailed information, please refer to the specific product pages.
If you have any other inquiries, please leave a message through the URLs below, and we will respond promptly.
For product inquiries: https://www.kitronyx.com/contact
For technical support inquiries: https://www.kitronyx.com/support_request
The Tinn / Baikal II wired products communicate with a PC via USB.
The Baikal II Wifi product is a dual-mode product that communicates with a PC via both USB and Wifi (2.4GHz, 802.11 g/n).
For other communication environments (such as RS232), custom development is required.
Please contact our sales team for further information.
Sales@kitronyx.com
If you have any other inquiries, please leave a message through the URLs below, and we will respond promptly.
For product inquiries: https://www.kitronyx.com/contact
For technical support inquiries: https://www.kitronyx.com/support_request
The measurement speed of the Baikal II depends on the communication environment:
32Hz in a wired environment and 21Hz in a wireless environment.
For faster measurement speeds, custom development is required.
We have developed solutions up to 600Hz.
Please refer to the demo video linked below.
If you have any other inquiries, please leave a message through the URLs below, and we will respond promptly.
For product inquiries: https://www.kitronyx.com/contact
For technical support inquiries: https://www.kitronyx.com/support_request
The controller itself does not support data storage or output functions.
If you use external programs and separate data processing devices (PLC, DAQ, etc.),
you cannot directly connect and communicate with the controller.
However, you can receive data through the PC software connected to the controller.
If you have any other inquiries, please leave a message through the URLs below, and we will respond promptly.
For product inquiries: https://www.kitronyx.com/contact
For technical support inquiries: https://www.kitronyx.com/support_request
With the purchase of a controller, a controller test board is provided to check for any malfunctions.
For detailed information, please refer to the attached Controller Test Board User Manual.
If you have any other inquiries, please leave a message through the URLs below, and we will respond promptly.
For product inquiries: https://www.kitronyx.com/contact
For technical support inquiries: https://www.kitronyx.com/support_request
controller test board manual_240715.pdf
135KBThe controller test board will be provided from the new controller package starting in April 2024.
Please inquire if you need a controller test board.
Link to how to use the controller test board
If you have any other inquiries, please leave a message through the URLs below, and we will respond promptly.
For product inquiries: https://www.kitronyx.com/contact
For technical support inquiries: https://www.kitronyx.com/support_request