Quick Start Guide for First-Time Users of the MP2513
Insole Sensor Kit
MP2513 Insole Sensor Kit
MP2513 Insole Sensor Kit Components
MP2513 Insole Sensor Kit Installation and Usage Guide
Follow the steps below to easily use the kit.
First, you need to install the Snowforce3 software.
1. Software Download
Click the download button to download the software.
※ Membership registration is required for the download.
2. Run the Installation File
Follow the installation guide to complete the installation.
※ During the installation, FTDI drivers and .NET Framework will be installed. Both must be installed.
In most cases, .NET Framework is already installed, so you may receive a message indicating it is already installed.
3. Run SnowForce3
4. Configure Software Device and Sensor
Set the device to Tinn (Snowboard2). (Default value: MC1509)
Set sensor 1 to INSOLE_M1_L and sensor 2 to INSOLE_M1_R. (Default value: None)
5. Set Device Port (Port1)
To connect the device with the software, you need to know the port number that identifies the device.
Click on Port1 UI, and you will see a Reset option. Depending on your PC, there might also be COM1.
Remember the port number, then refer to the image below to connect the Tinn controller to your PC.
After connecting to the PC, select Reset in Port1. A new COM port will be added.
The new COM port is the recently connected Tinn controller,
and the COM port number assigned by the PC usually does not change.
In this guide, COM81 is shown as the newly added port. Please select the new port.
6. Set Device Port (Port2)
Since the MP2513 Insole Sensor Kit uses two controllers, you need to repeat the above process one more time.
This time, click on the Port2 UI, remember the port number, and connect the second Tinn controller.
7. Connect Insole_L Sensor and Tinn Controller
Let's connect the Insole_L sensor to the first Tinn controller.
For Insole sensors, it is essential to use the M1 interface board.
Follow these steps to connect:
Refer to the image below.
※ Ensure that the arrow direction on the interface board points towards the front direction of the sensor when connecting.
8. Connect Insole_R Sensor and Tinn Controller
Similarly, let's connect the Insole_R sensor to the second Tinn controller.
Refer to the image below.
※ Ensure that the arrow direction on the interface board points towards the front direction of the sensor when connecting.
9. Start Measurement and Verify Operation
Press the Connect button to start the measurement.
To check if the connection is successful, press the sensor and verify that the pressed location appears correctly on the screen.
If it does not display, set the ColorMap value to 30 and the Threshold value to 0, then check again.
※ If it still does not display, please close SnowForce3 and start again from Step 3 (Run SnowForce3).
You have now completed the installation and operation verification of the MP2513 Insole Sensor Kit.
If you have any other inquiries, please leave a message through the URLs below, and we will respond promptly.
For product inquiries: https://www.kitronyx.com/contact
For technical support inquiries: https://www.kitronyx.com/support_request
- Post no.
- Title
- Author
- Time uploaded
- Views
- Updates and news Common [Document] Causes of Noise and Solutions N When using sensors, noise may sometimes be introduced, potentially affecting measurements.This docum...
- 박수지
- 9 hour(s) ago
- Views 22
-
- Updates and news Software [Document] ForceLAB2 Sensitivity Option Manual N ForceLAB2 includes a feature for adjusting the sensitivity scale of sensors.This feature is generall...
- 박수지
- 11 hour(s) ago
- Views 28
-
- Updates and news Software [Document] ForceLAB2 Log Post Processing Manual (Correcting Log Data Drift) [Download] / [View directly in browser]If you have any other inquiries, please leave a message throu...
- 박수지
- 18 Oct 2024
- Views 81
-
- Updates and news Software [Document] SnowForce3 Manual This is the manual for the free software, SnowForce3.Manual Update Date: September 12, 2024[Download...
- 박수지
- 12 Sep 2024
- Views 216
-
- Updates and news Controller [Document] Tinn User Manual This is the user manual for the Tinn product.It includes the specifications, components, and usage i...
- 박수지
- 2 Sep 2024
- Views 260
-
- Updates and news Controller [Document] Baikal II User Manual This is the user manual for Baikal II.It includes product specifications, configuration details, usa...
- 박수지
- 2 Sep 2024
- Views 313
-
- Updates and news Controller [Document] Baikal II WIFI User Manual This is the user manual for Baikal II WIFI.It includes product specifications, configuration details...
- 박수지
- 2 Sep 2024
- Views 319
-
- Updates and news Software [Document] User Calibration Guide Hello!this is Kitronyx, a leading company in the field of pressure distribution sensors.This post pr...
- 박수지
- 19 Jun 2024
- Views 651
-
- Updates and news Common [Document] Comprehensive Manual If you have any other inquiries, please leave a message through the URLs below, and we will respond ...
- 박수지
- 19 Jun 2024
- Views 770
-
- Updates and news Common [Document] Guide to Connecting 4 Sensors to Interface Board (MA2406) Hello!this is Kitronyx, a leading company in the field of pressure distribution sensors.In this post...
- 박수지
- 19 Jun 2024
- Views 478
-